-/* $OpenBSD: re.c,v 1.146 2013/10/25 22:48:10 brad Exp $ */
+/* $OpenBSD: re.c,v 1.147 2013/12/31 21:09:34 brad Exp $ */
/* $FreeBSD: if_re.c,v 1.31 2004/09/04 07:54:05 ru Exp $ */
/*
* Copyright (c) 1997, 1998-2003
int re_wol(struct ifnet*, int);
#endif
-#ifdef RE_DIAG
-int re_diag(struct rl_softc *);
-#endif
-
struct cfdriver re_cd = {
0, "re", DV_IFNET
};
CSR_WRITE_1(sc, RL_LDPS, 1);
}
-#ifdef RE_DIAG
-
-/*
- * The following routine is designed to test for a defect on some
- * 32-bit 8169 cards. Some of these NICs have the REQ64# and ACK64#
- * lines connected to the bus, however for a 32-bit only card, they
- * should be pulled high. The result of this defect is that the
- * NIC will not work right if you plug it into a 64-bit slot: DMA
- * operations will be done with 64-bit transfers, which will fail
- * because the 64-bit data lines aren't connected.
- *
- * There's no way to work around this (short of talking a soldering
- * iron to the board), however we can detect it. The method we use
- * here is to put the NIC into digital loopback mode, set the receiver
- * to promiscuous mode, and then try to send a frame. We then compare
- * the frame data we sent to what was received. If the data matches,
- * then the NIC is working correctly, otherwise we know the user has
- * a defective NIC which has been mistakenly plugged into a 64-bit PCI
- * slot. In the latter case, there's no way the NIC can work correctly,
- * so we print out a message on the console and abort the device attach.
- */
-
-int
-re_diag(struct rl_softc *sc)
-{
- struct ifnet *ifp = &sc->sc_arpcom.ac_if;
- struct mbuf *m0;
- struct ether_header *eh;
- struct rl_rxsoft *rxs;
- struct rl_desc *cur_rx;
- bus_dmamap_t dmamap;
- u_int16_t status;
- u_int32_t rxstat;
- int total_len, i, s, error = 0, phyaddr;
- u_int8_t dst[] = { 0x00, 'h', 'e', 'l', 'l', 'o' };
- u_int8_t src[] = { 0x00, 'w', 'o', 'r', 'l', 'd' };
-
- DPRINTF(("inside re_diag\n"));
- /* Allocate a single mbuf */
-
- MGETHDR(m0, M_DONTWAIT, MT_DATA);
- if (m0 == NULL)
- return (ENOBUFS);
-
- /*
- * Initialize the NIC in test mode. This sets the chip up
- * so that it can send and receive frames, but performs the
- * following special functions:
- * - Puts receiver in promiscuous mode
- * - Enables digital loopback mode
- * - Leaves interrupts turned off
- */
-
- ifp->if_flags |= IFF_PROMISC;
- sc->rl_testmode = 1;
- re_reset(sc);
- re_init(ifp);
- sc->rl_flags |= RL_FLAG_LINK;
- if (sc->sc_hwrev == RL_HWREV_8139CPLUS)
- phyaddr = 0;
- else
- phyaddr = 1;
-
- re_miibus_writereg((struct device *)sc, phyaddr, MII_BMCR,
- BMCR_RESET);
- for (i = 0; i < RL_TIMEOUT; i++) {
- status = re_miibus_readreg((struct device *)sc,
- phyaddr, MII_BMCR);
- if (!(status & BMCR_RESET))
- break;
- }
-
- re_miibus_writereg((struct device *)sc, phyaddr, MII_BMCR,
- BMCR_LOOP);
- CSR_WRITE_2(sc, RL_ISR, RL_INTRS);
-
- DELAY(100000);
-
- /* Put some data in the mbuf */
-
- eh = mtod(m0, struct ether_header *);
- bcopy ((char *)&dst, eh->ether_dhost, ETHER_ADDR_LEN);
- bcopy ((char *)&src, eh->ether_shost, ETHER_ADDR_LEN);
- eh->ether_type = htons(ETHERTYPE_IP);
- m0->m_pkthdr.len = m0->m_len = ETHER_MIN_LEN - ETHER_CRC_LEN;
-
- /*
- * Queue the packet, start transmission.
- */
-
- CSR_WRITE_2(sc, RL_ISR, 0xFFFF);
- s = splnet();
- IFQ_ENQUEUE(&ifp->if_snd, m0, NULL, error);
- re_start(ifp);
- splx(s);
- m0 = NULL;
-
- DPRINTF(("re_diag: transmission started\n"));
-
- /* Wait for it to propagate through the chip */
-
- DELAY(100000);
- for (i = 0; i < RL_TIMEOUT; i++) {
- status = CSR_READ_2(sc, RL_ISR);
- CSR_WRITE_2(sc, RL_ISR, status);
- if ((status & (RL_ISR_TIMEOUT_EXPIRED|RL_ISR_RX_OK)) ==
- (RL_ISR_TIMEOUT_EXPIRED|RL_ISR_RX_OK))
- break;
- DELAY(10);
- }
- if (i == RL_TIMEOUT) {
- printf("%s: diagnostic failed, failed to receive packet "
- "in loopback mode\n", sc->sc_dev.dv_xname);
- error = EIO;
- goto done;
- }
-
- /*
- * The packet should have been dumped into the first
- * entry in the RX DMA ring. Grab it from there.
- */
-
- rxs = &sc->rl_ldata.rl_rxsoft[0];
- dmamap = rxs->rxs_dmamap;
- bus_dmamap_sync(sc->sc_dmat, dmamap, 0, dmamap->dm_mapsize,
- BUS_DMASYNC_POSTREAD);
- bus_dmamap_unload(sc->sc_dmat, dmamap);
-
- m0 = rxs->rxs_mbuf;
- rxs->rxs_mbuf = NULL;
- eh = mtod(m0, struct ether_header *);
-
- RL_RXDESCSYNC(sc, 0, BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE);
- cur_rx = &sc->rl_ldata.rl_rx_list[0];
- rxstat = letoh32(cur_rx->rl_cmdstat);
- total_len = rxstat & sc->rl_rxlenmask;
-
- if (total_len != ETHER_MIN_LEN) {
- printf("%s: diagnostic failed, received short packet\n",
- sc->sc_dev.dv_xname);
- error = EIO;
- goto done;
- }
-
- DPRINTF(("re_diag: packet received\n"));
-
- /* Test that the received packet data matches what we sent. */
-
- if (bcmp((char *)&eh->ether_dhost, (char *)&dst, ETHER_ADDR_LEN) ||
- bcmp((char *)&eh->ether_shost, (char *)&src, ETHER_ADDR_LEN) ||
- ntohs(eh->ether_type) != ETHERTYPE_IP) {
- printf("%s: WARNING, DMA FAILURE!\n", sc->sc_dev.dv_xname);
- printf("%s: expected TX data: %s",
- sc->sc_dev.dv_xname, ether_sprintf(dst));
- printf("/%s/0x%x\n", ether_sprintf(src), ETHERTYPE_IP);
- printf("%s: received RX data: %s",
- sc->sc_dev.dv_xname,
- ether_sprintf(eh->ether_dhost));
- printf("/%s/0x%x\n", ether_sprintf(eh->ether_shost),
- ntohs(eh->ether_type));
- printf("%s: You may have a defective 32-bit NIC plugged "
- "into a 64-bit PCI slot.\n", sc->sc_dev.dv_xname);
- printf("%s: Please re-install the NIC in a 32-bit slot "
- "for proper operation.\n", sc->sc_dev.dv_xname);
- printf("%s: Read the re(4) man page for more details.\n",
- sc->sc_dev.dv_xname);
- error = EIO;
- }
-
-done:
- /* Turn interface off, release resources */
- sc->rl_testmode = 0;
- sc->rl_flags &= ~RL_FLAG_LINK;
- ifp->if_flags &= ~IFF_PROMISC;
- re_stop(ifp);
- if (m0 != NULL)
- m_freem(m0);
- DPRINTF(("leaving re_diag\n"));
-
- return (error);
-}
-
-#endif
-
#ifdef __armish__
/*
* Thecus N2100 doesn't store the full mac address in eeprom
if_attach(ifp);
ether_ifattach(ifp);
-#ifdef RE_DIAG
- /*
- * Perform hardware diagnostic on the original RTL8169.
- * Some 32-bit cards were incorrectly wired and would
- * malfunction if plugged into a 64-bit slot.
- */
- if (sc->sc_hwrev == RL_HWREV_8169) {
- error = re_diag(sc);
- if (error) {
- printf("%s: attach aborted due to hardware diag failure\n",
- sc->sc_dev.dv_xname);
- ether_ifdetach(ifp);
- goto fail_8;
- }
- }
-#endif
-
return (0);
fail_8:
projects / openbsd / commitdiff